Below you will find our High Voltage DC Power Supplies
These Are Not Static Machines, but Powerful Sources of Usable Current of up to 100ma
(These power supplies are normally used with positive output, but negative output is also available if required.)
Intended for laboratories and research, as used by physicists, experimenters, and industry for special projects. These devices have a range of current output from microamps to milliamps, voltages from 5 to 500kV, and most are voltage regulated and current regulated. Most of the devices on this page can be purchased as-is. However, if options are required they can be discussed by contacting us either by email or a phone call. Products that are considered potentially hazardous are so noted in their description. Some of the lower powered items can run from batteries or wall power, but the higher power units require wall power.
Reduced output current is achieved by using the included shock-reducing lead which limits average current to 200uA, allowing for high voltage output with a minimal shock hazard. This mode is useful for reducing often annoying shocks when working in cold plasma (where many interesting experiments produce visual and seemingly amazing displays), ion generation, corona, static electric fields, and other low-current experiments. May be used by younger students to perform many classroom functions with adult supervision. Demonstrates Ion motors and propulsion, charge projection, wireless object electrification, generate harmless shocks at a distance, force fields, EMP effects on sensitive electronic devices, wireless energy transmission, electro-metal spinning and many other experiments, applications etc. NOTE: This low current mode also provides a convenient way of testing capacitors and multiplier circuits to verify performance before potting is done, preventing costly rework.
Adjustable output up to 30kV at 1 milliamp / 35kV at 700ua / open circuit voltage may exceed 35kV at loads < 700ua.
Front panel adjustable voltage control from 500v to 35kv with analog voltmeter, panel lamp indicates “in or out” of regulation.
Output is voltage regulated through the output current range.
Two HV output leads are included: a shock-reducing lead for limiting annoying shocks, and a normal lead for full power operation. Easily switch between them by plugging in to the output connector.
Open- and short-circuit protected.
The high volt output common return lead exits thru the rear panel. It is end point grounded and connected direct to the base of the multiplier section. This lead must be used for all HV returns
Unit is powered by an included 3-wire grounded 12VDC 5A adapter (runs on 100-240VAC wall power for both US and international use).
Small and light weight, approximately 10"L x 7.5"W x 3.1"H. Made of an ABS Heavy Duty Plastic.
Highly reliable device can be used for powering ion sources, anti-gravity lifters, object charging, EMP experimenting, electro kinetic and pulse magnetic systems. Excellent for many laboratory and research applications.
This unit has been approved by our testing labs to be around younger students and hobbyists. Nevertheless, qualified adult supervision is suggested.
Click Above For Video of HV350 in Use
Note: NEVER power 12V electronics from 12V battery chargers, as the chargers can operate up to 20V and may ruin your circuitry. Battery chargers should only be used to charge batteries, never as power supplies.
Excellent for Generating Cold Plasma, Powering Small Marx Generators, Charging Capacitors Energy Storage Banks and Devices Where You Control the Energy by changing the Current. Powers Our Anti-Gravity Lifter Science Projects and Many Other Applications. The advantage of the controlled current source is realized in the charging of capacitors used for high-energy storage single event discharges intended for rail guns and other electro kinetic and EMP devices. Even at the time the charging cycle starts the current is controlled and remains relatively constant through the charging cycle. The source can also be short circuited where the current is still in a controlled mode. The charge voltage (vt)= f(t) x I all divided by C. This is a linear relationship and does not require the power wasting series resistance used for voltage sources. The disadvantage is that there is a tendency for the voltage to soar above the design ratings. Operation requires preventative measures such as monitoring the charge voltage or an electronic trigger that shuts the sources off when the desired charging voltage is reached
Adjustable output up to 30kV at 1 milliamp / 35kV at 700ua / open circuit voltage may exceed 35kV at loads < 700ua.
Front panel adjustable voltage control from 500v to 35kv with analog voltmeter.
Output is voltage regulated through the output current range.
Two HV output leads are included: a shock-reducing lead for limiting annoying shocks, and a normal lead for full power operation. Easily switch between them by plugging in to the output connector.
Open- and short-circuit protected.
The high volt output common return lead exits thru the rear panel. It is end point grounded and connected direct to the base of the multiplier section. This lead must be used for all HV returns
Unit is powered by an included 3-wire grounded 12VDC 5A adapter (runs on 100-240VAC wall power for both US and international use).
Small and light weight, approximately 8"L x 4.25"W x 4.5"H. Weight of 1.5Lb's Made with an aluminum base with a military gray PVC cover.
Highly reliable device can be used for powering ion sources, anti-gravity lifters, object charging, EMP experimenting, electro kinetic and pulse magnetic systems. Excellent for many laboratory and research applications.
This unit has been approved by our testing labs to be around younger students and hobbyists. Nevertheless, qualified adult supervision is suggested.
Click Above For Video of HV350 in Use
Note: NEVER power 12V electronics from 12V battery chargers, as the chargers can operate up to 20V and may ruin your circuitry. Battery chargers should only be used to charge batteries, never as power supplies.
Voltages from 10 to 40kV from a 9-14V DC input • For the Hobbyist, Student and Experimenter. Many high voltage projects can be built around these “ready to use” working modules.
CH40
Easily battery powered for many uses, from handheld defense devices, to science project lightning displays, to Plasma and Ion sources!
These low powered devices may be used for battery or solar applications. They are short circuit proof and suitable for capacitor charging without a current limiting resistor. They may also be used as low power high voltage power supplies. Units produce power and can give a nasty shock. These are not static electric machines!
DC powered (by battery or wall adapter) high voltage module is capable of charging capacitors and other field worthy applications. Can operate from a 9-14VDC battery pack or wall adapter (not included) and can fit into a small plastic tube of approximately 1.5" ID. This module is available at several maximum output levels that can supply from 10kV up to 40kV output (tap points along the HV multiplier stack for lower voltage outputs in 5kV to 10kV steps, or vary the input from 9-14VDC for adjustable output voltage, but do not exceed 14VDC input or the HV power supply can be overdriven and damaged).
Note: these multipliers are powered by our NEONXUL (MINIMAX30) driver. For higher output (roughly 50% greater final voltage), use our MINIMAX70 driver.
Standard output is normally positive (+), butnegative (-) output is also available -- please choose when ordering, as the units cannot be switched between positive and negative output due to the diode orientation on the multiplier stack. Kit versions may be built - or + depending on how you wire the diodes.
Intended for many applications including school science and hobbyist projects.
Available in Positive or Negative Output.
These low powered devices may be used with 12V battery or solar applications. They are short circuit proof and suitable for capacitor charging without a current limiting resistor. They may also be used as low power high voltage power supplies.
At last an affordable virtually indestructible source of high voltage for the student, hobbyist and professional. Now be able to experiment with continuous high voltage spark discharges, negative or positive ion generation, high speed ion propulsion motors, capacitor charging, animal and pest control, shocking applications, night vision power supplies, powering Crookes tubes, Geiger tubes, material testing, corona and Saint Elmo's fire, static generation, flocking devices, ion ray guns etc.
Circuit produces 25kV in 5kV steps open circuit with a short circuit current of less than 1ma, providing a reasonably save high voltage source. Load line is set favorable to ion emitting devices with a high megohm resistor. Circuit has built in open and full short circuit protection and can operate at full output indefinitely. Operation is from any 12 volt 2 amp dc regulated wall adapter, battery or converter (a 12V regulated wall adapter is included which runs off standard 115VAC wall power, and automatically converts to 230VAC for overseas customers). Dimensions are 6" L x 7" H x 2" W.
This device is best-suited for use with our ceramic capacitors or similar (taking care to not overcharge the smaller capacitors). An external voltmeter is required to monitor charge. Small value capacitors must be charged by quickly applying power as voltage value can be easily exceeded.
Device is basically a two part system consisting of a high voltage high frequency power supply connected into our five stage open multiplier allowing tap downs in 5 kV increments. This product would cost many times more than our asking price and is available in volume or individual purchases.
Normally these are used with positive (+) output, but negative (-) output is also available if required.
Create your own bright, white, hot noisy real lightning bolts for a winning science project, or a low cost laboratory source of 100kv for many applications.
Please note unit can give an annoying to painful shock if improperly handled but is not dangerous.
Here is your answer to a low cost high voltage source that will withstand open circuit, short circuit discharging with bright hot open air sparks 3 to 6 in length!
Perform a Demonstration of Lightning, Ozone Generation, High Flux Ion Generator, High Speed Ion Motor Propulsion, Plasma Blast Drilling, Hi Pot and Dielectric Testing, Self- Electrification, Capacitor Charging, Particle Acceleration and Many Other High Potential Low Current Electrical Experiments. Use as a wake up alarm or a great Halloween prop or gift. Even make a model electric chair with a doll or facsimile off your favorite politician, friend or girlfriend as a morbid joke. Two of these units made in opposite polarities can create a very active lightning show generating loud noisy lightning bolts up to 12" in length! Can be made in a very effective street defense or intimidation device!
100KV @ 200µa Fixed Output With Built-in Dry Filled Multiplier (drive frequency to multiplier ~60-70kHz)
Note: these devices are made to order and require 2-4 weeks build & test time before they can be shipped to you. Call for delivery schedule
We now offer our low cost adjustable regulated voltage power supplies intended for serious laboratory experimentation in anti gravity research, EMP, lossless capacitor charging and many applications requiring a reliable medium source of regulated high voltage.
Two part system consists of (1) control console attached to the (2) voltage multiplier via an umbilical cable. Circuit includes an over voltage shutdown with full short circuit protection and a voltage indicating analog meter. Basic 115 vac at 60 hz operation runs off standard wall power (220V for international operation requires a stepdown transformer such as our TR220/110/500 or you may have one on-hand; just be sure it is sufficient wattage for your power supply).
Normally these are used with positive (+) output, but negative (-) output is also available if required.
Note: these devices are made to order and require 3-6 weeks build & test time before they can be shipped to you. Call for delivery schedule and any options you may require.
With Variable Output and Other Features
Two-part system consists of (1) control console attached to the (2) voltage multiplier via an umbilical cable. Circuit includes an over voltage shutdown with full short circuit protection and a voltage indicating analog meter. Basic 115 vac at 60 hz operation runs off standard wall power (220V for international operation requires a stepdown transformer such as our TR220/110/1500 or you may have one on-hand; just be sure it is sufficient wattage for your power supply).
Adjustable Regulated Voltage up to 400,000 DC Volts with Positive or Negative Output Available
Excellent for Capacitor Charging as Short Circuit Operable
Adjustable Current shutdown setting manually set by operator
Adjustable Current over Range of Device Ratings
Two Part Construction Consisting of 24" to 72" Cylindrical
Dry Fill Multiplier Tower (Oil Fill Option Available)
Over Voltage Fault Shutdown
High Voltage Output Panel Meter
Output Current Panel Meter
Input Current to Driver Circuit Panel meter
Optional Designs Available
Please contact us for any options you may require. Products can be positive (+) or negative (-) output upon request.
Necessary for all HHO or similar projects requiring ignition or detonation from a safe distance See the below video clips
You will need this trigger to ignite (from a safe distance) the HHO gas mixture that drives our hydrogen action science projects, or any explosive or dangerous material
The control box which has a safety arming switch and a push button fire control switch and a 9 volt battery.
An LED indicator alerts the user that the system is armed. The control box also houses the batteries.
The interconnecting cable is sufficiently long (about 25-30 feet) to provide ample separation between the material and the operator. If you need more distance, simply add a wiring extension.
The 20kv ignitor module is connected closely to the actual device but out of the sympathetic range of damage.
Lastly, about 2-3 feet of high voltage output wire and a grounding lead are connected to the target to ignite
Include a very simple electric field, static charges and high frequency potentials often found around gas discharge lighting, high potential radiating alternating current fields often found near high tension power lines and other sources such as radio transmitters.
High voltage measuring probes are used for actual contact measuring dc potentials up to 200kv.
NOT INTENDED FOR ACTUAL CONTACT TO HIGH VOLTAGE POINT AS MAY CAUSE A LETHAL OR SERIOUS SHOCK
Radiant Energy Probe and E-Field Detector
USE CAUTION AROUND HIGH VOLTAGE NEVER CONTACT OR USE CLOSE TO A KNOWN HIGH VOLTAGE POINT
Probe detects E fields produced by electrical activity and other unknown anomalies. Unit uses no batteries or other sources of power. Unit can also provide a three dimensional output "footprint" of medical healing machines such as LAKHOVSKY coils, High voltage generators, Ion machines, Dangerous lightning levels, Power line E field gradients, High frequency radiation from TESLA coils and similar devices. This probe is used by paranormal researchers as seen on some TV shows.
This device is for detecting moderately weak E fields, like those from plasma globes, tesla coils, ion generators, etc. It is not intended for weak E fields, like those generated by many household items. If you need something to detect household or weaker energy fields, we suggest our IOD40.
The apparatus is electrically balanced and designed in the shape of a wand with a 2 inch brass sphere at its detecting end. The handle is 1” OD x 9” of treated polycarbonate with plated metallic tape wrapped around the ends. A red neon indicator lamp (a standard bulb that should last for years, but can easily be replaced if needed) flashes upon detection and increases as you get closer to the source, or if the source gets stronger.
Probe detects:
Potential free energy field locations
Electric fields produced by ions sources
Dangerous static charges
Paranormal and UFO energy fields
High frequency radiation
Weather phenomena lightning
High voltage leakage points
Plotting a three dimensional footprint of E-fields of HV sources
Detects strange and otherwise unidentifiable sources
This handy unit is easy to use and can check the validity of output energy of various healing machines and other radiating products. It is a must-have product for those working in these energy fields.
HV50PROBE: Measures either positive or negative DC voltages up to 50KV. Input impedance of 1000 megohm draws only 50 µa from circuit at 50 kv (50,000 ohms/volt). Removable 2” brass corona sphere reduces leakage for those sensitive measurements. Probe is approximately 2 feet in length.
HV250PROBE: Like the HV50PROBE but at 250KV, with a 4" sphere, and 4.5 feet in length.
Polarity Switch
Full 24" length plastic enclosure (51" for HV250PROBE)
Flexible 5’ grounding lead with heavy crocodile clip
Detects both positive and negative electric fields produced by ions, ultra low static fields, lightning, paranormal entities and other associated phenomona by using a special DC amplifier and low leakage switch. Very useful device in warning of approaching dangerous storms.
ALL NEW IOD40 detects both positive and negative electric fields produced by ions, ultra low static fields, lightning, paranormal entities and other associated phenomona by using a special low leakage switch.
This very versatile tool detects both positive and negative electric fields produced by ions, and ultra low static fields This unit is sensitive enough to detect the minute charge produced by just rubbing a piece of plastic and bringing the probe in proximity. It easily measures the electric field during a thunder storm or other high static conditions long before the storm arrives.
Extremely useful for mapping the electric fields associated with high voltage generators. Indicates dangerous "E" fields that may damage sensitive electronic circuits or components. Detects those that can be dangerous to personnel. Detects the presence of weak to strong static charges from lightning, potential corona points and output of ion generators, leaking high voltage insulators and wiring insulation. A very valuable device for the high voltage researcher and experimenter.
Unit is built into a handheld 5" x 3" x 1.75" Plastic box with extendable detection antenna probe. Simple high performance circuitry is powered by a single 9 volt battery that seldom needs replacement.
Detector indicates field strength using an analog meter with a sensitivity control. Includes a potential dangerous high charge field condition by an indicating LED. Switch selects positive or negative charge fields. A response switch allows fast or slow response. A simple external terminal provides a connection point for a grounding lead. Front-mounted RCA phono jack provides a facsimile out for remote monitoring or trigger circuitry for alarms, x/y recorder, etc.
It has been observed that certain paranormal activity is often accompanied by a distortion of the electric field. These changing fields are usually too weak to be detected by conventional detectors. The IOD40 has on several occasions detected unexplained fields in coincidence with other events. At the time of this writing a study is being done at several selected grave sites to see if the distortion in these weak fields can be detected and correlated with other unexplained events.
Capacitor Chargers -- manual & programmable, for charging capacitors from 100V to 35kV Ion Power & Motors -- HVDC output optimized for maximum ion creation Capacitor Dischargers & Ignitors -- for safe ignition and controlled release of stored capacitor energy Spark Gap & Rail Switches -- for large controlled energy discharges up to 120kV and 5MA (mega-amps) HV Measuring Aids -- to measure the energy field or direct high voltage output up to 250kV Van de Graaff Generators -- high voltage machines capable of generating up to 500kV output
Loading... Please wait...
Brief Overview on HVDC Power Supplies & Functions
 "img-6428-150-200.jpg")
)
)
)
)
 "iod40small-s.png")
