Transformers
Home | New Products | Gift Ideas | Plans | Policies | Contact Us
Transformer/Coil Manufacturing | Engineering & Design Services
To order: click the ITEM NUMBER
to add to your shopping cart
|
|
TransformersHome | New Products | Gift Ideas | Plans | Policies | Contact Us Transformer/Coil Manufacturing | Engineering & Design Services |
To order: click the ITEM NUMBER
|
Volume discounts are readily available.
|
|
|
|
45KV output at .5 JOULES, 50-10ms exponential ring down time. 1.25" round by 1.25" long in fully potted enclosure. CD45 - Transformer...............$29.95 |
|
|
40KV peak at 10ma with large ferrite core measuring 3 ¾ x 3 ½ x 5/8”allows adequate clearance for higher voltage windings. 15kHz-60kHz operating frequency. Easy to wind primary of your choice. Allows more clearance for higher operating voltages of the below coil sections shown for PVM400 & 500. Here is an example of a PVM500 schematic.
FLYPVM+ - 40kV 10mA Transformer....................$69.95 |
FLYPVM400 |
20KV peak at 20ma, current limited 15kHz-60kHz operating frequency, with 3" size large UU60 ferrite core and flexible silicon output lead. 4000 turns #37 on secondary with silicon output lead. Primary is easily wound and takes from 50 to 100 turns dependent on input driving circuitry. Core is air gapped and can easily be changed if needed for controlling secondary current. For end point grounded circuits. Excellent for powering plasma loads, displays, jacob’s ladders or other negative resistance loads. Short circuit proof. (We can manufacture these, and variations, in large volume for the trade; contact us by phone 603-673-6493 or .) Here is an example of a PVM400 schematic.
FLYPVM400 - 20kV 20mA Transformer................$59.95 |
|
FLYPVM500 |
Similar looking to the FLYPVM400 but intended for resonant operation. 30KV peak at 20 ma, 15kHz-60kHz operating frequency, with 3" size large ferrite core and flexible silicon output lead. 2500 turns #35 on secondary with silicon output lead. Primary is easily wound and takes from 50 to 100 turns dependent on input driving circuitry. UU60 large core is air gapped and can easily be adjusted to change the resonant frequency. Output voltage will vary as to the external load complexity being the load capacity and resistance. For end point grounded circuits. (We can manufacture these, and variations, in large volume for the trade; contact us by phone 603-673-6493 or .) Here is an example of a PVM500 schematic.
FLYPVM500 - 30kV 20mA Transformer................$59.95 |
|
Capable of providing 10KV peak at 60ma, 15kHz-60kHz operating frequency. High output intended for CO2 lasers and as a driver for Cockroft Walton voltage multipliers up to 300KV at 2ma. With pre-wound primary and low voltage auxiliary. Low leakage inductance as primary and secondary are on same leg of a 2.75 x 1.325 x 0.675" U core set. Secondary is wound with 2500 turns of #34 wire. For endpoint grounded circuits. (We can manufacture these, and variations, in large volume for the trade; contact us by phone 603-673-6493 or .) An example of a working FLYLABURN circuit schematic is available by purchasing our
LABURN20 plans ($3.00) by download.
FLYLABURN - 10kV 60mA Transformer................$69.95 |
All cores are standard ferrite, for high voltage designs. Each U-core purchase comes as a set of two (2) pieces. Each rod comes as a set of a single (1) piece.
Free HV Ferrite Transformer Design
All Ferrite Core dimensions listed as (Height x Width x Thickness):
|
FC030201 - (0.345 x 0.20 x 0.160") ........$3.00/set
FC060402 - (0.610 x 0.44 x 0.260") ........$5.00/set FC080702 - (0.810 x 0.71 x 0.240") ........$5.00/set FC080602 - (0.875 x 0.60 x 0.225") ........$5.00/set FC100702 - (1.000 x 0.75 x 0.250") ........$5.00/set FC120803 - (1.290 x 0.88 x 0.390") ........$5.00/set |
FC130903 - (1.375 x 0.97 x 0.380") ........$5.00/set
FC151004 - (1.500 x 1.07 x 0.410") ........$7.50/set FC151104 - (1.500 x 1.10 x 0.430") ........$7.50/set FC161204 - (1.650 x 1.20 x 0.460") ......$10.00/set FC161205 - (1.630 x 1.20 x 0.570") ......$10.00/set |
|
|
FC3205 - Ferrite Rod, single (1) piece, 3.20" length x 0.5" diameter ......$5.00/ea |
|
Current-Limited Luminous Tube Transformer at 30ma and 6KV
6KV 30ma, centerpoint grounded secondary, current limited, encased unit with screw terminals. This transformer is excellent for small table top Tesla coils and is used in our new and revised BTC3K kit and BTC30 ready-to-use Tesla coils. Dimensions: 10 3/8 x 3 5/8 x 3 1/4” with a weight of 11.4lbs. Shipping weight is approximately 17 pounds and may exceed $25. 6KV/.03EN - Transformer...............$69.50 |
60ma transformers require signing our
|
DANGEROUS PRODUCT -- CAN CAUSE ELECTROCUTION IF IMPROPERLY HANDLED
We have purchased tooling for and now have our own current-limited luminous tube transformers at 60 ma with 15000 or 9000 volt output. These units will have our name with logo on them and are only available through us. They are also available for volume purchasing. These are brand new, factory-fresh transformers. They DO NOT contain the bothersome ground fault interrupter that makes them difficult to use for TESLA coils and other scientific applications. Operates from 115 vac and are easily parallel connected for higher power operation. (For example, six of the 15KV/60MA units connected in this way can produce 15000 vac rms at 360 ma. This is enough power to make a large TESLA coil easily producing 10+ foot arcs.) May also be connected for 7500 volts at 120 ma (9KV/60MA provides 4500v at 120ma).
|
Pole Transformer
|
DANGEROUS PRODUCT -- CAN CAUSE ELECTROCUTION IF IMPROPERLY HANDLED
Heavy duty 14.4KV (very conservatively rated), 1- or 2-bushing oil filled unit, running on 220/110VAC input. Good for Tesla Coils, up to 12 ft. discharges! Price does not include extra shipping and handling charges. Sold only to qualified researchers and labs.
5KVA14.4KV - 5 KVA 14.4 KV Pole Mount 240/480 1PH 2 Bush AL Wire ............$695.95
|
|
220VAC input with 12VDC/.1A output intended for low power circuits. Great for science projects. 1 ½ x 1 ¼" x 1 ¼" metal case with leads. Unused and originally boxed items. Purchase includes a 2-wire 6-foot polarized power cord. One order consists of 5 pieces.
12DC220 - 5 Transformers With Power Cords..............$20.00 |
|
Easy to wind bobbin for many electronic projects. Easy to use providing a wide range of voltages and currents. An example circuit schematic is included.
3 x 2-1/4" x 5/8", 3C80 material good for up to 1 mHz, u=2000, 500 watts
2 x 2-1/4" x 1/2", 3C80 material good for up to 1 mHz, u=2000, 300 watts
|
|
|
|
Email: Sales & Orders | Email: Tech Support |
|
|
PO Box 716, Amherst, NH 03031-0716 |
|
