Fully enclosed in a 5-1/2 X 5 x 2-1/4" plastic flame-retardant box with pull chain switch and 8-foot 3-wire power cord. Temperature rated for continuous operation up to 85°C (185°F). 24" GTO flexible output leads. Guaranteed patented circuit eliminates mercury migration and actually restores most darkened displays to normal.

Fully enclosed in a plastic flame-retardant box with pull chain switch, 6-foot 3-wire power cord, and 24" GTO flexible output leads. Temperature rated for continuous operation up to 60°C (140°F). Guaranteed patented circuit eliminates mercury migration and actually restores most darkened displays to normal.

CPI-6-35 - UL2161 Transformer, 6kv 35ma 120v ...............$49.50
CPI-6035 - Non-UL Transformer, 6kv 35ma 120v ..............$49.50

CPI-10-35 - UL2161 Transformer, 10kv 35ma 120v ..........$69.50
CPI-10035 - Non-UL Transformer, 10kv 35ma 120v .........$69.50
CPI-10035FL - Non-UL (Flashing) 10kv 35ma 120v ..........$79.50
CPI-10035DM - Non-UL (Dimming) 10kv 35ma 120v ........$81.50

CPI-EZ12 - UL2161 Transformer, 12kv 42mA 120v ............$72.50

UL Listed 4000 volts open circuit at 25-ma short circuit with safety shutdown in case of glass breakage or other faults. Short circuit protection with open circuit shutdown. Unit is easily animated by connection to a standard 3.5 mm phono jack input requiring a 5-volt level. Animators are available from simple flashing to multi-programmable units controlling up to four individual SUPERGLOS for a fully animated system.. The unit is enclosed in a 4 ½ X 2" flame retardant box with a pull chain switch. Full six foot 3 wire grounded power cord and 2 foot out put leads. Intended for neon displays up to 15 feet. Operates 115 vac at .5 amps.

NEONIZER

Small thumb-sized unit operates from included 12VAC/0.5 amp wall adapter, or directly from a 12V battery source for wireless operation. Device will light up a 24" piece of 12 mm thick neon tube using only one electrode. Can also be used with gas display figurines without electrodes by capacitance feed. Powers 2-4' displays. Connects to closest electrode. Open frame construction of 1 x 1 x 3" is easily enclosed for small specialized neon art pieces.

Free PDF Instructions

If you need a power supply, our 12 volt 0.5 amp wall adapter is available
(just clip off the jack & strip the leads for use with the NEONIZER):
12DC/.5 - Wall Adapter for NEONIZER ..........................................$5.95

NEON21

Open frame with potted transformer 5 x 1-1/4". Lights over 12 feet of 12 mm tubing from a single electrode. Excellent for small plasma globes and other gas filled figurines, "luminglass" plates and other small gas filled objects.

Free PDF Instructions

If you need a power supply, our 12-14 volt 1 amp wall adapter with grounded third pin
eliminates the external ground wire often necessary for larger single ended displays:
14DC/1G - Wall Adapter for NEON21 .....................................................$19.95

NEON21/115 - NEON21 Transformer + 14DC/1G Wall Adapter ......$49.95

• Independent voltage control from zero to maximum output of 20 kv pk-pk
• Independent current control from 5% to maximum output
• Independent frequency control from 20 khz to 50 khz
• Large 3" ammeter monitors AC line current. Indicates resonance peaking
• Adjustable wave form duty cycle function allowing a wide range of display textures
• Adjustable safety shutdown circuit disables the circuit in case of over voltage
• Maximum output power over 200 watts
• Short circuit proof by built in leakage reactance
• 120vac 50/60 hz input (240 vac versions available with auto step down transformer, below)
• Powers the smallest to the largest displays
• Measures 7" x 4" x 10" and weighs less than 5 pounds.

Now at last a reliable and flexible power supply to effectively drive those light capacitive loads. Output power may be adjusted from 10 to 200 watts. Utility unit operates from standard wall power (120 vac 60 hz) and measures 7 x 4 x 10" and weighs less than 5 pounds. Intended for hydrogen production research, corona generation, energizing dielectric barrier junctions, ozone production and other electrochemical applications.

FEATURES:
OUTPUT - Variable 1-20kv
FREQUENCY - Variable 15-35khz
CURRENT - Reactance Limited to 25 ma.
INPUT - 115/220 50/60hz 1-2 amps
SAFETY - Over Voltage Shutdown Manual Reset
OPTIONS - Flashing, Sound and Music Control, and Pulsed Duty Cycle Attachments Available

As above PVM400, but with Optional Features.

Free Instructions   |   Free Schematic

1. This model PVM400DELUX has a built-in controller that allows you to change the display texture over a considerable range. This feature greatly enhances the display effect by controlling the ratio of pulse on to off times.

2. Contains a 3.5 mm audio jack that accepts a 5 volt level allowing the unit to flash to any external source. Excellent effect when activated in coincidence to the base beat of any music system when using our BASEBEAT10 as shown below. Unit can be made to flash at a 50/50 rate from 1 to 30 flashes per second with the below FLASH10. Multiple units up to four displays may be activated by our 10 program ANIMATOR40 shown below.

PVM12

Adapter for PVM12
12 Volts 3 Amps, Fully Regulated. Operates from 100 to 240 vac. 5 foot output cable with a 2.1 and 2.5 mm output plug. Included IEC power cord. UL and CUL CE FCC Recognized.
12DC/3AR ..............$29.95