Loading... Please wait...


Our Newsletter

EMP Electro Magnetic Pulse


laser pointers

EMP stands for electromagnetic pulse. It can be produced by a nuclear detonation, a lightning discharge or any type of a discharge that can take on a form of a pulse with a fast rise time. Obviously a nuclear air burst produces EMP by releasing intense gamma ray radiation into the Earth's magnetic field where now a myriad of radio frequencies is generated due to the fast rise time and other Fourier properties. These type of pulses Occur and cause wide spread damage to many electronic circuits. computers and similar circuits are very vulnerable to this type of energy as it does not take many volts applied across the junctions of these high-speed circuits to disrupt their operation . When the EMP pulse contacts the printed circuitry of the system, a standing wave of voltage is produced and damages the circuitry components causing destruction.

A lightning discharge can be characterized as a natural manifestation of an EMP pulse. It is in the form of a double exponential pulse where the risetime is very fast and the decay time is much slower. The discharge current of a lightning bolt could be close to a mega Amp. This combined with the risetime of the current pulse can cause damage as we all well know. The overall charge of a lightning bolt is usually in from 1 to 50 coulombs. The discharge voltage being in the hundreds of thousands creates an energy pulse in the megajoules. Joules = coulombs times voltage.

A demonstration generated electromagnetic pulse can be made by discharging a ultralow high volt capacitor into a low inductance antenna.

EMP/HERF/Shock Pulse Generator

- Paper Plans ... $20.00
- Downloadable Plans ... $10.00
Shock wave generators are capable of producing focused acoustic or electromagnetic energy that can break up objects such as kidney stones and other similar materials. EMP generators can produce pulses of electromagnetic energy that can destroy the sensitive electronics in computers and microprocessors. Destabilized LCR circuits can produce multi megawatt pulses by using an explosive wire disruptive switch. These high power pulses can be coupled "with difficulty" into antennas, conic sections, horns etc for very directional effects. Research is currently being undertaken to disable vehicles thus avoiding dangerous high speed chases. The trick is to generate a high enough power pulse to fry the electronic control processor modules without creating collateral damage to unintended targets. This could be a lot simpler if the vehicle was covered in plastic or fiber glass rather than metal. The shielding of the metal body offers a challenge to the researcher to develop a practical system. A system could be built that could do this but would be costly, large and produce collateral damage to friendly targets.
Component Parts and Accessories

Parabolic Reflectors (click for more detailed information)
- Dia 305mm, Foc Len 76mm ... $79.95
- Dia 457mm, Foc Len 114mm ... $99.95
- Dia 610mm, Foc Len 152mm ... $139.95

Ultra Low Inductance Capacitor (click for more detailed information)
- New .1µfd 100kV 25kA ... $1095.00

Low Cost 100KV DC Power Supply (click for more detailed information)
- Assembled ... $249.95
- Kit/Plans ... $179.95
- Paper Plans ... $8.00
- Downloadable Plans ... $4.00

Low Power Pulse Gun
Hand held pulse gun generates EMP electromagnetic pulses capable of de-programming and disrupting micro processor circuitry.

Low powered hand held pulse gun generates EMP electromagnetic pulses capable of de-programming and disrupting micro processor circuitry. Gun is built in a pistol configuration where the 8 "AA" batteries are housed in the butt section along with the push button trigger switch.

Directional device has adjustable pulse rate control and a built in emitter for close proximity applications. Specialized circuitry use our ultra low inductance high energy density capacitors with self triggering gap switch. Charging circuit uses our loss-less inductive charging and eliminates the losses associated with simple resistive methods. Pulse energy is approximately 1 Joule with a rep rate up to 30 pps. Charging voltage is over 5kv with a peak current of nearly 1000 amps now equal to a 5 megawatt pulse of power.

Output terminals may be adapted for a wave guide for more precise applications or connection to an external antenna where you can experiment with maximizing "E" or "M" field for certain applications. Unit can be built in a military gray PVC enclosure measuring 10 to 12 inches. *Assembled units are sold only to qualified personal who submit their order on a company letter head.

- Kit & Plans ... $199.50
- Paper Plans ... $15.00
- Downloadable Plans ... $7.00

High Power Pulse Generator / Gun
Advanced unit intended for experienced personnel in this field wanting to experiment with coupling and pulse emission methods

Assembled pulse wave generators in choice of 12 vdc or 115 vac. Pulse rate up to 20 per minute - Requires emitter antenna and waveguide parallel terminated transmission line (not included).

Attention to those wanting to build their own EMP Pulse Gun

We now have assembly schematics, instruction booklet, 20 colored photos of construction, and other data for those wanting to build a medium- to high-power pulse source. Plans show using the latest fast-discharge 100kV Maxwell high energy density capacitor capable of 1200 joules energy storage. This energy is switched using the latest triggered spark switching technology providing very steep rise times at multi-gigawatt peak powers. Included data shows Current controlled programmable charger, Trigger circuitry, Discharge circuit and all other necessary data. Antennas and wave guides are shown.

- Assembly Data, Schematics, Full Color Photos and Instruction Booklet ... $15.00
- Downloadable Assembly Data, Schematics, Full Color Photos and Instruction Booklet ... $5.00

Complete Shock Pulse Systems Crated With All Setup Instructions

Sold only to qualified research companies and personnel

Model Output Weight
EMP150 300 Megawatts 90 kg/198 lbs
EMP400 1.8 Gigawatts 170 kg/374 lbs
- 150 Joules, 15 KV, 20 KA ... $9850.00
- Downloadable Instructions ... $1.00
- 400 Joules, 40 KV, 45 KA ... $17700.00
- Downloadable Instructions ... $2.00

Contact Us For Any Special Handling You May Require

Electromagnetic EMP Blaster Gun, Gen II



A 10-stage Marx generator built of ten 10nf per stage provides 1nf of erected capacitance. This section is built into a pressure chamber of 210mm diameter & 2500mm length. The Marx generator is fed by a three-stage high voltage power supply with an input of 230 volts 50/60Hz. This D.C. to D.C. converter generates 0 to 20kV DC which is fed to the Marx input for charging the capacitors.

The Marx output of 90kV to 160kV pulse is fed to a peaking capacitor of 30pf to 180pf for shaping the pulse. The output peaking gap is fixed to shape the pulse further. The Marx now charges the output capacitor. This capacitor (coaxial oil filled capacitor) discharges into the load through the peaking gap. The entire system is coaxial made further enhancing the effectiveness.


  • Random HV Generator.
  • HV HF Source for plasma Generation.
  • Pulse Power Source for Z-Pinch study.
  • High Voltage High Current Linear Injector.
  • Use as a emp Generator with a properly designed TEM Cell.

The EMP pulser with a special Antenna is capable of shutting down a computer at a distance of 15 meters. It generates a steep 2 nanosecond rise time >2 Giga-watt pulse into a parallel plate transmission line type of Antenna.

The "EMP Blaster Gun" is suitable for many small experiments requiring radiating EMP waves. The system utilizes a high voltage discharge of 100Kv to 160Kv at a pulse repetitive rate of 1pps. It can also ignite highly explosive fuels in close proximity or contact.

When fixed with a parallel plate antenna, even of mismatched impedance, about 15Kv / meter are produced at a distance of 2 meters (with a generated voltage of 160Kv output). With a coaxial design, the radiated waveform will have a rise time of under 50 nanoseconds, and a field strength of 15 to 30Kv / meter at distance of 1 to 2 meters.

Please note that the system will fail if operated into a short circuit.

General specifications for the "EMP Blaster Gun" are as follows:
  • Operating voltage : 230 volts / 50 Hz or 110 volts / 60 Hz
  • Maximum output : 160Kv 13 Joule pulse of Rise time < 50 nanoseconds.
  • Maximum PRR at 1 pps duty 1 minute ON & 5 Minutes OFF
  • Gas required : Dry Nitrogen at a pressure of 30 PSI (2 Atmosphere)
  • The system utilizes a 10 stage Marx Generator with peaking gap.
  • Coaxial constructed in a stainless steel metal cylinder 210 cm in diameter.
  • 90kV to 160kV maximum by mechanical adjustment of spark gaps inside the construction as also from gas pressure variation
  • Capacitance per stage : 10nf / 20kV
  • Erected capacitance : 1nf / 20kV
  • Impedance of the system : 40 Ohms
  • Length of System : 2.5meters
  • Diameter of System : 300mm overall
  • Weight : Generator < 175kg; Antenna 30kg; Total 205kg maximum


- Electromagnetic Pulse Gun ... Priced Upon Request


- Paper Instructions ... $15.00
- Downloadable Instructions ... $5.00

Accessories and Components for EMP Devices

Energy Probe

Radiant Energy Probe and E-Field Detector

Probe detects E fields produced by electrical activity and other unknown anomalies. Unit uses no batteries or other sources of power. Unit can also provide a three from TESLA coils and similar devices. This probe is used by paranormal researchers as seen on some TV shows.

This device is for detecting strong E fields, like those from plasma globes, tesla coils, ion generators, etc. It is not intended for weak E fields, like those generated by many household items. If you need something to detect household or weaker energy fields, we suggest our IOD40.

The apparatus is electrically balanced and designed in the shape of a wand with a 2 inch brass sphere at its detecting end. The handle is 1” OD x 9” of treated polycarbonate with plated metallic tape wrapped around the ends. A red neon indicator lamp (a standard bulb that should last for years, but can easily be replaced if needed) flashes upon detection and increases as you get closer to the source, or if the source gets stronger.

Probe detects:

  • Potential free energy field locations
  • Electric fields produced by ions sources
  • Dangerous static charges
  • Paranormal and UFO energy fields
  • High frequency radiation
  • Weather phenomena lightning
  • High voltage leakage points
  • Plotting a three dimensional footprint of E-fields of HV sources
  • Detects strange and otherwise unidentifiable sources

This handy unit is easy to use and can check the validity of output energy of various healing machines and other radiating products. It is a must-have product for those working in these energy fields.

- Assembled ... $34.95

Parabolic Reflectors
For Above EMP Generators

Made of polished aluminum, with center hole and mounting rim.

- Dia 305mm, Foc Len 76mm ... $79.95
- Dia 457mm, Foc Len 114mm ... $99.95
- Dia 610mm, Foc Len 152mm ... $139.95

Ultra Low Inductance Capacitors
Intended for use in Research devices requiring very high peak currents such as MARX impulse generators, EMP, Shock pulsers, wire exploding for nano particle generation and other devices requiring fast rise time high peak current power pulses.
Oil Filled Energy Storage Capacitor

All new ultra-low inductance high voltage specialized capacitors for EMP, Marx generators, voltage multipliers and other high voltage ultrafast discharge applications. Capacitors are mineral oil filled, cylindrically shaped and have 3/8” diameter brass studs for connections to flat bar or other heavy conductors. Dimensions are 3.5" diameter x 2.5” length (plus 1" terminals). Discharge current > 30,000 amps.

- 1µfd @ 5kv 10 nh Capacitor ... $119.95

Low Inductance Capacitor

These low inductance capacitors are excellent for EMP shock pulse generators, Lithoscopy, exploding wires, Marx impulse generators, Slapper detonators, plasma focused neutron enriching, gas discharge lasers, thermonuclear research, high magnetic fields, etc.

Voltage Rating: 100kV
Capacitance: 0.1uf ±10%
Inductance: 18~25nH (about .02uH)
Design Life: 3x104
Repetition Rate: ≤ 1/s
Max Current: 25kA Peak; 25A RMS
Operating Temp: -10C to +45C
Physical: 2.5x6x16" at 7.5 pounds, oil impregnated (non-PCB)

- Ultra Low Inductance Capacitor ... $1095.00

Low Inductance Capacitor

These low inductance capacitors are excellent for EMP shock pulse generators, exploding wires, Marx impulse generators, Slapper detonators, plasma focused neutron enriching, gas discharge lasers, thermonuclear research, high magnetic fields, etc.

.05µfd 50kV, 30A in a cylindrical tube 3" x 3" x 17"

These capacitors may take ~4 weeks to build.

- Low Inductance Capacitor ... $319.95

Oil Filled Energy Storage Capacitors

Scyllac Type
1.3 Microfarad 100,000 Volt Pulse Discharge Capacitor

Here is the holy grail of high energy fast discharge capacitors. These large units are the dream components of many high voltage, high energy experimenters. Capacitor is rated 1.3 µfd at 100,000 volts at a 60,000 amp discharge capability, giving 6500 Joules. Ultra low inductance is excellent for shock pulsers, wire exploding, EMP generation, etc. Units measure 14”L x 11”W x 25”H and weigh 230 pounds with ground ring terminations. Capacitors are strapped on pallets for shipping by truck. The original cost of these units are about $6700.00 each (if you can find them for sale). Our price is significantly less.

Used and in excellent working condition, these capacitors have been randomly sampled and found that they test to 95% or greater of rated specs.

- Low Inductance Scyllac Capacitor ... CONTACT US FOR CURRENT PRICING

Due to the size and weight of these capacitors, shipping by freight is required and may be different from what is shown in the shopping cart. Contact us by phone or email to get an accurate shipping quote, or to set up your own shipping carrier.

Rail Gap Switches

High coulomb energy transfer switches intended for rail guns and other electro-kinetic devices. Require nitrogen gas at 10PSI. 35-page brochure on operation and assembly of these precision machined devices fully refundable with purchase.
- 15 to 40Kv at 1Mega-Amp ... Price Upon Request
- 10 to 16Kv at 300Kilo-Amp ... Price Upon Request

- 2KV at 1Mega-Amp ... Price Upon Request

- Brochure ... $20.00


100KV 200µa Power Supply (Fixed Output)
High Voltage DC Power Supply Low Cost 100KV @ 200µa Fixed Output With Built-in Dry Filled Multiplier
12VDC or 115VAC Input

  • Runs on 115VAC for Lab (with included wall adapter), or 12VDC for Field Use
  • Adjustable Safety Gap
  • Dry Fill Multiplier
  • Available as a Project Kit and Plans
  • Table Top 4" x 18" Cylinderical Design
  • Light Weight -- Less Than Five Pounds
  • Excellent Science Project

Available Option for Portable 12vdc Operation:
- Rechargeable 12V/7AH Battery For Field Use , 6 x 2.5 x 3.7" ... $29.95
HVOLT10 Video
- Ready to Use 12vdc/115vac ... $249.95 $199.95
- Kit/Plans ... $179.95 $149.95
- Paper Plans ... $8.00
- Downloadable Plans ... $4.00