All solid state infra red lasers feature ultra compact construction, long lifetime, low cost and are easy to operate. Lasers are used in communications, instrument, spectrum analysis, interference, measurement, holography, sensing inspection, physics experiments etc.
Wavelength (nm)
946
1047
1053
1064
1319
1342
Output Power (mw)
1-200
1-100
1-200
1-1000
1-200
1-500
Laser Crystal
Nd:YAG
Nd:YLF
Nd:YLF
Nd:YVO4
Nd:YAG
Nd:YVO4
Transverse mode TEM00
Operating mode CW
Power stability (rms, over 4 hours) Select <1%,<3%,<5%
Warm up time (minutes) <15
M 2 factor <1.5
Beam divergence, full angle (mrad) <1.5.0
Beam diameter at aperture (mm) ~3.0
Beam height from base (mm) 24.8
Spectral linewidth (nm) <0.1
Point Stability After Warmup (mrad) <.05
Noise amplitude (rms) <.1%
Operating temperature (C) 10-35
Expected lifetime (hours) 10,000
Laser head dimensions (mm) 142 L x 73W x 46 H wgt .645 kg
Power supply dimensions (mm) 135 L x 130 W x 61 H wgt 1 kg
All solid state infra red lasers feature ultra compact construction, long lifetime, low cost and are easy to operate. Lasers are used in communications, instrument, spectrum analysis, interference, measurement, holography, sensing inspection, physics experiments etc.
Wavelength (nm)
946
1064
1342
Output Power (mw)
300-500
1500-2000
1000-1500
Laser Crystal
Nd:YAG
Nd:YVO4
Nd:YVO4
Transverse mode TEM00
Operating mode CW
Power stability (rms, over 4 hours) Select <1%,<3%,<5%,<10%
Warm up time (minutes) <15
M2 factor <2
Beam divergence, full angle (mrad) <2
Beam diameter at aperture (mm) ~3.0
Beam height from base (mm) 29
Polarization ratio >100:1
Spectral linewidth (nm) <0.1
Point Stability After Warmup (mrad) <.05
Noise amplitude (rms) <.1%
Operating temperature (C) 10-35
Expected lifetime (hours) 10,000
Laser head dimensions (mm) 155 L x 77W x 60 H wgt .86 kg
Power supply dimensions (mm) 238L x 146 W x 94 H wgt 2.88 kg
Power supply 80-260 vac
Warranty time 1 year
TTL modulation Optional, 1-10 kHz ...40 kHz on request
Analog modulation Optional, 1-10 kHz ...or higher, 0-5 volt
Power stability (rms, over 4 hours) Select <1%,<3%,<5%
Warm up time (minutes) <15
M2 factor <2
Beam divergence, full angle (mrad) <2
Beam diameter at aperture (mm) ~5.0
Beam height from base (mm) 93.5
Polarization ratio >100:1
Spectral linewidth (nm) <0.1
Point Stability After Warmup (mrad) <.05
Noise amplitude (rms) <.1%
Operating temperature (C) 10-35
Expected lifetime (hours) 10,000
Laser Head dimensions 333 L x 140W x 125 H 8 kg
Power supply available 110 or 220 vac 50-60Hz
Power supply dimensions (mm) 324 L x 277 W x 142 H 13 kg Laser head dimensions (mm)
Warranty time 1 year
TTL modulation Optional up t0...30 kHz on request
Analog modulation Optional, up to ...30 khz on request
Item s highlighted in red are options.
30 Milliwatt Continous Infra-Red Laser Module
High power invisible 30 milliwatt red laser at 980 nanometers operates on 3 volts (two AA batteries) This module is a Class 3b device and requires protective eyewear when viewing the beam or any potential direct reflections or scatter. Intended for experimental use in window bounce systems, target designation, optical x-rays, IR holography and general optical research. The module may be temporarily powered with just a 3 volt battery pack. Module measures 1 ½"' x ½" diameter and includes an adjustable collimating lens. Excellent value includes our instructions on how to build a fully compliant Class 3b laser system.
Illumination source for
night vision, target
designation controller and laser bounce systems
long range optical voice communicators etc..
30 mw@980 nm, Battery powered with focusing lens and collimator in 1x8” cylinderical enclosure. Simple retrofit to test tone and voice modulator circuits. Protective eyewear suggested when viewing direct reflections experiments!
30 mw@980 nm
1 milliradian Divergence
Input 3 volts@ 60ma
Includes x7 Collimator
Class IIIB Compliant
Cylindrical 7" Length
Available As Kit or Assembly
CWL2 - Plans(By Download - $4.00) ...........$10.00 CWL2K - Kit/Plans............................................$199.95 CWL20 - Lab Assembled................................$299.95Infra Red Pulsed Lasers Use of These Class 3B Devices Requires Protective
Eye Wear When Viewing The Laser Beam
These lasers are rated at 10 to 100 watts of peak power. This level of power only exists for the defined duration of the pulse. If these pulses are integrated for a one second period, you now have the energy expressed in Joules.
The advantage of a pulsed system is that the pulses are optically equivalent to the peak power level as rated and can be detected with a suitable detection system that will see them at this power level.
The equivalent energy that the laser system now requires is only a fraction and is related to the repetition rate x the peak power x the pulse duration and is approximately equal to Joules.
NOTE:
A Joule is a watt second and is "energy". If that energy is released in 1 micro-second as a pulse, the power of that pulse is now 1 megawatt!!! Note a laser pointer at 5 milliwatts equates out to the pulsed laser being 200 MILLION times brighter!!!
A useful application of these two devices is use as a laser property guard security fence around a home or other premise.
A very suitable detector for this pulsed laser is our Laser Light Detector.
Note a laser pointer is 5 milliwatts equating out to the pulsed laser being 5000 times more detectable!
Infra Red Pulsed Lasers
Devices emit variable rate and power pulses of infra
red energy at 9000A. This type laser is easy to construct and operate. Its versatility
is high efficiency, durability and small size. Applications range from fiber optic
communications, target illumination, simulated weapons fire, long range optical
link, high resolution radar, ranging, intrusion detection, etc. Power requirements
are 115 VAC or batteries for portable field operation. Peak Power To 100 Watts!
Battery Operated Version Of Above
Portable Field Model
Internal Batteries - 10 Hrs
Trigger Switch
Single Pulse or
Multiple Operation
800 To 1100 nm Wave Length
Pulse Rate 200 to 2000 PPS
Pulse Width 200 ns
All FDA Compliances
With Collimator “C” mount attachment
LRG6-
Plans...................................................................$15.00 LRG6K- Kit/Plans with 10-15 Watt Diode................$299.95 LRG60 - Lab Assembled with 10-15 Watt Diode....$499.95
High Peak Power 904 Nm Pulsed Laser Diodes
These diodes produce a 200 nanosec maximum pulse width. All diodes are full spec and unused. All purchases include our SSL5 pulsed infrared laser plans showing operational circuitry and applications. We stock this laser product as a kit, fully assembled or you may purchase the individual parts.
Contact the factory for quantity discounts at 1-603-673-6493
Laser Pulse Detector For Above Laser Systems
High Speed Pin diode detector with wide band amplifier compatible with high speed laser diodes with nanosecond rise times. Board level module is ground plane constructed. Easy retrofit expanded pulse circuitry, etc.. Includes basic optics.