High Voltage, High Frequency Power Supplies DC Power Supplies | High Freq (AC) Power Supplies Home | New Products | Gift Ideas | Plans | Policies | Contact Us Transformer/Coil Manufacturing | Engineering & Design Services

To order: click the ITEM NUMBER to add to your shopping cart

All New - Full Feature
PVM500 Plasma Driver

Please note that we can design a transformer to match your cell capacitance. Contact us by phone or email to get a quote or discuss your needs.

Important: This model is an advanced system intended for use by qualified personnel, familiar with driving resonant circuits. We do not offer refunds on this equipment, but will of course repair it if a problem should develop. Please make sure you have any questions answered before purchasing this item.

NOTE: the PVM500 shown here and DIDRIV10 (shown below) are basically the same but are used for different applications.

Independent voltage control from zero to maximum output of 20kv pk-pk Independent current control from 5% to maximum output Independent frequency control from 20 kHz to 70 kHz Large 3" ammeter monitors AC line current. Indicates resonance peaking Adjustable wave form duty cycle function allowing a wide range of operation Maximum output power over 200 watts Short circuit proof by built in leakage reactance 120vac 50/60 Hz input (240 vac versions available with auto step down transformer, below) Measures 7 x 4 x 10" and weighs less than 5 pounds. Free Intructions   |   Free Schematic   |   Free Duty Cycle Writeup Now at last a reliable and flexible power supply to effectively drive those light capacitive loads. Output power may be adjusted from 10 to 200 watts. Utility unit operates from standard wall power (120 vac 60 hz) and measures 7 x 4 x 10" and weighs less than 5 pounds. Intended for hydrogen production research, corona generation, energizing dielectric barrier junctions, ozone production and other electrochemical applications.

PVM500 - Ready to use ....................................................................................................................$449.95
TR220/110/300 - Optional 220V/50Hz Step Down Auto Transformer With European Plug ....$59.95

Dielectric Barrier Corona and Plasma Discharge Resonant Driver

Please note that we can design a transformer to match your cell capacitance if it does not fall within our basic range. Contact us by phone or email to get a quote for your specific needs.

Important: This model is an advanced system intended for use by qualified personnel, familiar with driving resonant circuits. We do not offer refunds on this equipment, but will of course repair it if a problem should develop. Please make sure you have any questions answered before purchasing this item.

Independent voltage control from zero to maximum output of 20kv pk-pk Independent current control from 5% to maximum output Independent frequency control from 20 kHz to 70 kHz Large 3" ammeter monitors AC line current. Indicates resonance peaking Adjustable wave form duty cycle function allowing a wide range of operation Maximum output power over 200 watts Short circuit proof by built in leakage reactance 120vac 50/60 Hz input (240 vac versions available with auto step down transformer below) Powers the smallest to the largest displays Measures 7 x 4 x 10" and weighs less than 5 pounds Free Intructions   |   Free Schematic   |   Free Duty Cycle Writeup Now at last a reliable and flexible power supply to effectively drive those light capacitive loads. Output power may be adjusted from 10 to 200 watts. Utility unit operates from standard wall power (120 vac 60 hz) and measures 7 x 4 x 10" and weighs less than 5 pounds. Intended for hydrogen production research, corona generation, energizing dielectric barrier junctions, ozone production and other electrochemical applications.

Universal High Voltage Modular Power Supply

Out put voltage is a 60 kHz high frequency current that is fully short circuit protected. The high frequency also makes possible low storage energy voltage multiplier stacks for high voltage dc sources as well as being an excellent plasma driver when used direct. Output current is fully adjustable via a control pot. Unit is excellent for powering neon and all types of gas filled vessels using one or two electrodes or can power objects simply by proximity.

It easily retrofits to our voltage multipliers modules providing DC voltages up to 100 kv and currents of up to 0.3 milliampere. The current limiting and control feature make this combination an excellent choice for charging capacitors for low loss charging and 12 volt portable operation.

Also an excellent choice for powering large and small anti gravity craft and other applications requiring a high voltage current controlled source.

Module is built on a rugged printed circuit board and is mounted in a plastic channel. Complete with input and out put leads.

Open circuit voltage to 7500 peak at 60 to 125 kHz Short circuit current.............10 ma Short circuit protected, open circuit adjustable overvolt safety gap Input: 11 to 15 volts DC at 3 amps fully loaded Adjustable current by duty cycle controlled pulse 7" output leads 12" input leads Compact 7" x 2-1/8" x 1-1/8" size weighing less than 5 ounces! Easily retrofits to our voltage multipliers

GRADRIV1 - Plans (By Download - $4.00) ...................................$8.00
GRADRIV1K - Kit/Plans ..................................................................$49.50

MINIMAX Series Modules

MINIMAX3 - 3Kv open circuit at 20 ma short circuit, requiring 12 vdc at 800 ma. Full metal enclosure. 2" x 1-½". Easily generates 15 kv at 1 ma with our five stage multiplier. UL approved unit.
	Quantity   MINIMAX3 - 3000 Volt Module .........$19.95 10-24 @ $14.95ea.  25-99 @ $13.95ea.  100+ @ $11.95ea. 12DC/.8 - 12vdc/.8 amp 115 vac Wall Adapter ...................$8.95

MINIMAX4 - 4Kv open circuit at 15 ma short circuit, requiring 12 vdc at 1 amp. Open frame. 4-1/4" x 1" x 1-3/8". Easily generates 20 kv at 1 ma with our five stage multiplier. UL approved unit.
	Free Instructions Quantity   MINIMAX4 - 4000 Volt Module .........$19.95 10-24 @ $14.95ea.  25-99 @ $13.95ea.  100+ @ $11.95ea. 12DC/1AR - 12vdc/1 amp 115 vac Wall Adapter (full output) .......$12.95

MINIMAX7 - 7kv open circuit at 10 ma short circuit requiring 12-14 vdc at 1000 ma. Open frame with potted transformer 5 x 1" (Free Instructions). Easily generates 30 kv at 0.5 ma with our five stage multiplier.

MINIMAX7P - 7000 Volt Module Plans (By Download - $3.00) ..............................$5.00 Quantity   MINIMAX7 - 7000 Volt Module .................................................$34.95 10-24 @ $29.95ea.  25-99 @ $26.95ea.  100+ @ $22.95ea. 12DC/1.5 - 12vdc/1.5 amp 115 vac Wall Adapter ....................................................$15.95 14DC/1G - 14vdc/1amp Adapter with Grounding Pin for Single End Displays ..$19.95

5 Stage Low Power Voltage Multiplier

Plasma, Gas Discharge, and Jacob's Ladder Power Supplies

Patented circuitry is UL approved with full short circuit, ground fault, and open circuit safety shutdown.

UL Approved XL1035 10,000 volts open circuit at 35-ma short circuit with two level power switch. Fully enclosed 5 ½ x 5 x 2 ¼" with power cord and pull chain switch. UL 2161 for full usage in trade. Temperature rated for continuous operation up to 85°C (185°F). Operates 115 vac at 2 amps. Quantity   XL1035 - Transformer .............$59.95 10-49 @ $44.95ea.  50-99 @ $39.95ea.  100+ @ $35.95ea.

Single Ended or Contactless
Gas Discharge Power Supplies

These devices are excellent when combined with a Cockcroft Walton voltage multiplier for lossless capacitor charging.

NEONIZER

Small thumbed sized unit operates from included 12vac 0.5 amp wall adapter. Device will power up a 24" piece of 12 mm thick discharge tube using only one electrode. Open frame construction of 3/4" height x 5/8" width x 3.75" length is easily enclosed for small laboratory applications. Quantity   NEONIZER - Transformer ...........$29.95 10-24 @ $24.95ea.  25-99 @ $21.95ea.  100+ @ $19.95ea.

PVM400

INPUT - 115 or 220VAC, 1-2 amps (plugs directly into wall outlet) OUTPUT - Variable 1-20kv FREQUENCY - Variable 20-60khz CURRENT - Reactance Limited to 25 ma SAFETY - Over Voltage Shutdown Manual Reset OPTIONS - Flashing, Sound and Music Control, and Pulsed Duty Cycle Attachments Available High-powered front panel adjustable output plasma driver operates from 115 or 220 vac and is intended for large plasma-globes, columns and large gas filled discharge vessels up to 30 inches. Rectangular shaped unit is 2 x 3 x 10" deep and is built on an aluminum chassis with plastic cover. A 2 x 3" panel contains the fuse power adjust control, indicator lamp and power cord exit. Output end is open with a 12" 30 Kv high voltage and 4' grounding lead. Factory set open circuit voltage shutdown protects the transformer from too light and no load operation. Internal circuitry protects against short circuits. Open circuit voltage is 20 Kv with a short circuit current of 25 ma load lines at 125 watts of output. The power adjust control varies the frequency from 20 to 60 kHz and controls output current. Full load output line current is 1.5 amps. This unit can also be used with a high voltage multiplier stack for obtaining DC voltages over 100 Kv. This setup allows current charging of high energy capacitors without the need for "lossy" current limiting resistors. Free Instructions   |   Free Schematic Quantity   PVM400 - Transformer ...................$199.95 5-9 @ $179.95ea.  10+@ $149.95ea. Quantity   PVM400-220 - Transformer at 220V for Overseas Customers .....$199.95 5-9 @ $179.95ea.  10+@ $149.95ea.

PVM400DELUX

Powers up to 48" Plasma Globes Single Electrode Operation As above PVM400, but with Optional Features. Free Instructions   |   Free Schematic   |   Free Duty Cycle Writeup 1. This model PVM400DELUX has a built-in controller that allows you to change the display texture over a considerable range. This feature greatly enhances the display effect by controlling the ratio of pulse on to off times. 2. Contains a 3.5 mm audio jack that accepts a 5 volt level allowing the unit to flash to any external source. Excellent effect when activated in coincidence to the base beat of any music system when using our BASEBEAT10 as shown below. Unit can be made to flash at a 50/50 rate from 1 to 30 flashes per second with the below FLASH10. Multiple units up to four displays may be activated by our 10 program ANIMATOR40 shown below.

Free Instructions	Base Beat Musical Light Flasher ATTENTION Music Lovers! Neon light tubes flash to the musical base beats Neat action display Great add on to existing music systems Small control unit interfaces with our PVM400DELUX transformer (or any transformer with an audio/animation control input) and controls large plasma displays (such as our plasma globes) or many feet of neon tubing, by flashing along with the base beat of the music. Unit is ready to use as-is or can easily be housed in any suitable enclosure. Built-in microphone eliminates hardwired hookup to a sound system. Easy to use, just adjust knobs for desired effect. BASEBEAT10 - Ready to Use..............$59.95
	FLASHER Flashes a single PVM400DELUX or two in anti-coincidence -- that is, one "off" the other "on" and reversing. Mating plugs fit into the PVM400DELUX unit. Adjustable flash rate. FLASH10 - Ready to Use .....................$29.95
	ANIMATOR Four channel operation controls four PVM400DELUX's with up to ten selectable programs with a digital readout. Animation speed is adjustable. Complete with mating plugs. Custom programs on request. ANIMATOR40 - Ready to Use ..............$69.95

Energy Probe

Radiant Energy Probe and E-Field Detector ENPROBE10 - Assembled ......$34.95

Probe detects E fields produced by electrical activity and other unknown anomalies. Unit uses no batteries or other sources of power yet detects very weak and virtually un-noticed energy fields. Unit can also provide a three dimensional output "footprint" of medical healing machines such as LAKHOVSKY coils, High voltage generators, Ion machines, Dangerous lightning levels, Power line E field gradients, High frequency radiation from TESLA coils and similar devices. This probe is used by paranormal researchers as seen on some TV shows. This device is for detecting strong E fields, like those from plasma globes, tesla coils, ion generators, etc. It is not intended for weak E fields, like those generated by many household items. If you need something to detect household or weaker energy fields, we suggest our IOD10. The apparatus is electrically balanced and designed in the shape of a wand with a 2 inch brass sphere at its detecting end. The handle is 1” OD x 9” of treated polycarbonate with plated metallic tape wrapped around the ends. A red neon indicator lamp (a standard bulb that should last for years, but can easily be replaced if needed) flashes upon detection and increases as you get closer to the source, or if the source gets stronger. This handy unit is easy to use and can check the validity of output energy of various healing machines and other radiating products. It is a must-have product for those working in these energy fields. Probe detects: Potential free energy field locations Electric fields produced by ions sources Dangerous static charges Paranormal and UFO energy fields High frequency radiation Weather phenomena lightning High voltage leakage points Plotting a three dimensional footprint of E-fields of HV sources Detects strange and otherwise unidentifiable sources

Orders: 603-673-6493 | Fax: 603-672-5406 Email: Sales & Orders | Email: Tech Support

PO Box 716, Amherst, NH 03031-0716