PO Box 716, Amherst, NH 03031-0716
	High Voltage DC Power Supplies

         

To order, click the ITEM NUMBER to add to your shopping cart.

The advantages of the current source are realized in the charging of capacitors used for high-energy storage single event discharges intended for rail guns and other electro kinetic and EMP devices. Even at the time the charging cycle starts the current is controlled and remains relatively constant through the charging cycle. The source can also be short circuited where the current is still in a controlled mode. The charge voltage (vt)= f(t) x I all divided by C. This is a linear relationship and does not require the power wasting series resistance used for voltage sources. The disadvantage is that there is a tendency for the voltage to soar above the design ratings. Operation requires preventative measures such as monitoring the charge voltage or an electronic trigger that shuts the sources off when the desired charging voltage is reached.

The advantage of the voltage source approach is the property of maintaining a constant voltage value within the design limits required as current (load) is being drawn. This is an advantage for electric- field charging when used for accelerators, ion beams, isotope enrichment , particle beams, potential generators etc. The disadvantage is that current is not controlled and overloads can damage the circuitry. Charging capacitors now require a power robbing series resistance to control the current. Charging is exponential. Our HVOLTV high power series utilize a bit of both worlds being voltage and current sources by user selection.

Capacitor chargers can also be used as power supplies.

SPECIAL NOTE ON CHARGING CAPACITORS

DANGER -- charged capacitors can kill you by electrocution, and cause very serious injury from burns and explosions. Do not attempt to use this equipment unless completely educated in high voltage circuitry. These products are intended for experienced laboratory personnel.

Programmable capacitor chargers allow you to dial in the charging voltage and view the event via a front panel analog meter. Capacitors charge from a current source and waste little energy such as that when using a ballast resistor. Ballasted energy is all reactive and never is consumed as real power.

A selector switch is included allowing charge cycle to cease once the preprogrammed value is reached. It can be selected to automatically recycle the charging function keeping the capacitor up to voltage until the charger is turned off or the event occurs.

The charging time can be estimated by calculating the energy in joules of the capacitor being charged and dividing by joules (watt-sec) of the charger. This is only approximate as it assumes linear power being applied throughout the charge cycle.

You can more accurately approximate the charging time of your capacitors by using the simple formula t=cv/i, where t = sec, c = capacity in farads, v = voltage, and i = charging current in amps.

Excellent to use for capacitor integrity testing or just as a charger for laboratory functions and experiments.

Optional designs are available in preferred voltage and current value.

2000 Volt DC Power Supply
(Continuous output)

Requires caution as output can produce a very painful electric shock and is not intended for human contact!

SHK1 - Plans..............Free Download
SHK1K - Kit/Plans..................................................................$29.95
SHK10 - Assembled Module (shown)...............................$39.95

      12DC/.5 - 115vac Wall Adapter (12v 0.5a output) .......$5.95
      12DC/.3 - 115vac Wall Adapter (12v 0.3a output) .....$3.50

Low Powered High Voltage Ceramic Capacitor Charger and Test Jig

These low powered devices may be used for battery or solar applications. They are short circuit proof and suitable for capacitor charging without a current limiting resistor. They may also be used as low power high voltage power supplies.

Charges capacitors to rated voltage and allows to set for determining excessive internal leakage Small lightweight unit measuring 5-½ x 2-¼ x 1-½” converts 12 vdc to over 30kv dc for charging capacitors or just supplying a potential. Can be used with 8 AA alkaline batteries that can produce >90,000 Joules!, or just use our #12DC/.5 wall adapter for 115 vac operation. Free PDF Instructions PBK50M - Assembled Unboxed Power Supply .....$39.95 PBK50 - Assembled Power Supply ..........................$49.95 12DC/.3 - 12 Volt .3 amp Wall Adapter for PBK50 ....$3.50

Capacitor Charging or Low Power HV Supplies These low powered devices may be used for battery or solar applications. They are short circuit proof and suitable for capacitor charging without a current limiting resistor. They may also be used as low power high voltage power supplies. CHARGE05

Battery powered high voltage module is capable of charging capacitors and other field worthy applications. Operates from an 8 "AA", 12Vdc battery pack and can fit into a 1 ½" plastic tube. Generates 5000 volts DC at 5ma. as shown. This module can supply up to 20,000 volts and is available in the following output levels: CHARGE1 - Plans for 5-20KV (By Download - $3.00) .......$5.00 CHARGE05 - 5000 volts at 5ma ..........................................$49.95 CHARGE05K - Kit/Plans 5000 volts at 5ma ......................$34.95 CHARGE10 - 10,000 volts at 2.5ma ...................................$59.95 CHARGE10K - Kit/Plans 10,000 volts at 2.5ma ...............$39.95 CHARGE20 - 20,000 volts at 1ma .......................................$69.95 CHARGE20K - Kit/Plans 20,000 volts at 1ma ...................$44.95

Electrolytic Capacitor Charger

Low Power 800V 30mA Manually Programmable Charger for Electrolytic, Photo Flash and Other Equivalent Capacitors

EXTREMELY DANGEROUS PRODUCT ONLY SOLD TO QUALIFIED LABORATORY PERSONNEL. OTHERWISE REQUIRES OUR HAZARDOUS EQUIPMENT AFFIDAVIT. Handy electronic circuit charges up electrolytic capacitors from 100 to 800 volts. Recommended capacities are between 100 to 5,000 mfd. This equates out to over 3000 joules! (Note that the kinetic energy of a .30-06 is 750 joules.) Units are manually voltage controlled by an internal adjustment that presets a charge indicator lamp when the required voltage is reached. This feature helps prevents over charging and potentially dangerous explosions. Charging is current controlled by our unique circuitry. Input power can be C or D cell batteries or 12 vdc adapter for direct 115 vac power. Charging rate is over 40 (watt-sec) joules. Size is 5 x 4 x 2” Free PDF Instructions DANGER A SERIOUS DEADLY SHOCK HAZARD EXISTS WHEN USING WITH HIGH ENERGY CAPACITORS ABOVE 50 JOULES. CHARGE800V - Assembled ready to use, charges up to 800 volts at 25 joule/sec .......$59.95

Automatic Programmable Charger / Power Supply

EXTREMELY DANGEROUS PRODUCT ONLY SOLD TO QUALIFIED LABORATORY PERSONNEL. OTHERWISE REQUIRES OUR HAZARDOUS EQUIPMENT AFFIDAVIT. Higher power electronic circuit charges up capacitors from 500 to 5000 volts at recommended capacities from 100 mfd and upwards. This equates out to over 40,000 joules with a 20,000mfd capacitor! Units are voltage programmable preset by the setting of the charge voltage control on the control panel. Capacitors automatically charge to and maintain this voltage until discharged. Charging is current controlled by our unique circuitry and indicated by a large analog panel meter. Input power can be either 115/230 vac power. Charging rate is > 400 watt-sec (joule)/sec. Size is 10-1/2 x 7 x 3-3/4" Free PDF Instructions DANGER A SERIOUS DEADLY SHOCK HAZARD EXISTS WHEN USING WITH HIGH ENERGY CAPACITORS ABOVE 50 JOULES. CHARGE500V - Assembled ready to use, charges up to 500 volts at 400 joule/sec ...........$395.00 CHARGE2000V - Assembled ready to use, charges up to 2000 volts at 400 joule/sec .......$495.00 CHARGE5000V - Assembled ready to use, charges up to 5000 volts at 400 joule/sec .......$595.00

These High Voltage power supplies produce relatively high currents that can be used for experimentation in anti-gravity, BI-FIELD BROWN, force fields, hovercraft research, plasma blasters, drillers, ion motors, propulsion, lightning generation, high ion source, ozone and air purification, electrification, particle acceleration, atom smashing, capacitor charging, general high voltage research, etc.

All power supplies are positive unless requested to be negative.

All New
Low Cost 25 KV DC Power Supply
Available in Positive or Negative Output

These low powered devices may be used for battery or solar applications. They are short circuit proof and suitable for capacitor charging without a current limiting resistor. They may also be used as low power high voltage power supplies.

At last an affordable virtually indestructible source of high voltage for the hobbyist and professional. Now be able to experiment with continuous high voltage spark discharges, negative or positive ion generation, high speed ion propulsion motors, capacitor charging, powering small anti gravity lifters, animal and pest control, shocking, night vision power supplies, powering Crookes tubes, Geiger tubes, material testing, corona and Saint Elmo's fire, static generation, flocking devices, ion ray guns etc.. Circuit produces 25 Kv open circuit with a short circuit current of less than 5 ma. providing a reasonably save high voltage source. Load line is set favorable to ion emitting devices. Circuit has built in open and full short circuit protection and can operate at full output indefinitely. Operation is from any 12 to 15 volt 1 amp dc wall adapter, battery or converter.

Device is basically a two part system consisting of a UL approved high voltage high frequency power supply connected into our five stage open multiplier allowing tap downs in 5 Kv increments. This product would cost many times more than our asking price and is available in volume or individual purchases.

HV25 : Plans (By Download - $3.00) .................................................................................................$6.00
HV25K : Kit of High Frequency Power Supply and Parts to Make the Multiplier ......................$39.95
HV250(+) : Assembled Multiplier with High Frequency Power Supply, Positive Output ........$64.95
HV250(-) : Assembled Multiplier with High Frequency Power Supply, Negative Output .......$64.95
14DC/1 : 14volt 1amp Adapter for 25KV Power Supply ..................................................................$9.95

35,000 Volt Low Cost Power Supply

All new 35 kilovolt at 1.5 milliamp power supply with adjustable current control is both short and open circuit protected. Small, lightweight unit is powered by 12v batteries for field use, or a low cost 12vdc/3amp converter for 115 vac use (both sold separately, below). Attractive, eye-catching unit has a clear plastic cover revealing the circuitry innards. Highly reliable device can be used for powering anti gravity lifters up to 4 feet on a side, or as an excellent current source for charging capacitors in EMP, electro kinetic and pulse magnetic systems. May also be used for many laboratory and research applications. Available as a kit or ready to use with options as listed. Current regulated version includes a 44 megohm 20 watt built in load resistor. Free PDF HV350 Instructions Current Regulated Version: HV35 - Plans (By Download - $5.00) ..........................................$10.00 HV35K - Kit and Plans .................................................................$159.95 HV350 - Ready to Use .................................................................$189.95 The HV---REG series (below) are similar to the above units but have the added feature of maintaining a constant voltage throughout its operating range. No load or load resistor is needed and voltage can be adjusted from 5000 to 35000 on our basic model when operating at < 1ma. Lower voltage higher current models are available on customer request (email us with your required specs). Voltage Regulated Version: HV050REG - Regulated 1000 to 5000 volt 5ma, ready to use ............$179.95 HV350REG - Regulated 5000 to 35000 volt 0.75ma, ready to use ....$199.95

Shockless High Voltage Supply

Generates 5-35kv of high voltage with a minimal shock hazard. Suggested use by younger experimenters, schools or beginners. Allows many experiments such as force fields, ion motors, corona and many other interesting projects.

Free PDF HV350 Instructions Features: Adjustable output from 5 to 35kv Short circuit current 100 uamps may be internally set up to 1 ma. Size: 4 x 4 x 8" Transparent cover for educational visibility Input of 12 volts dc at 1 amp via wall adapter or battery pack Output at resistor tower 12" silicon HV wire Front panel voltmeter Includes several experiment directions HV350SAFE - Assembled and Ready To Use ......................$199.50

Low Cost 100KV @ 200ua Fixed Output With Built-in Dry Filled Multiplier, 12VDC or 115VAC 115VAC Lab or 12VDC for Field Use Adjustable Safety Gap Dry Fill Multiplier Available as a Project Kit and Plans Table Top 4" x 18" Cylinderical Design Light Weight -- Less Than Five Pounds Excellent Science Project HVOLT1 - Plans (By Download - $4.00) ............................$8.00 HVOLT1K - Kit/Plans .........................................................$249.95 HVOLT10 - Ready to Use 12vdc/115vac .......................$349.95

Available Options for Portable 12vdc Operation

Power supply, converts 115 Vac wall power up to 13.8 Volts / 7 Amps. 12DC/7 - Ready to Use Converter .........$39.50	Rechargeable 12v Battery For Field Use BAT12/7 - 12V/7AH, 6 x 2.5 x 3.7" ......$24.95
Power supply, converts 115 Vac wall power to 12 Volts / 3 Amps. 12DC/3AR - Ready to Use Converter .......$29.95	Trickle Battery Charger For Above 12V battery, Charges in ~24 Hours. TCHARGER12K - Kit and Plans...........$14.95

50KV/5ma Adjustable Current Sourced Power Supply We now offer our low cost 50KV/5ma adjustable current sourced power supply intended for serious experimentation in anti gravity research, EMP, lossless capacitor charging and other related applications. Two part system consists of CONTROL CONSOLE attached to the VOLTAGE MULTIPLIER via an umbilical cable. Circuit includes an over voltage shutdown with full short circuit protection and a voltage indicating analog meter. 115/220 at 50/60 hz operation. HVOLT5V : Plans (By Download - $7.00) ................................................$15.00 HVOLT50V(+) : 50KV@4000+uA, Positive Output, Ready to Use .....$899.95 HVOLT50V(-) : 50KV@4000+uA, Negative Output, Ready to Use ....$899.95

Higher Powered Units

Note: these devices are made to order and require 2-4 weeks build & test time before we can ship them to you. Adjustable Regulated Voltage up to 300,000 DC Volts Positive or Negative Available Current over 2000 micro-amps Choice of 115 / 220 VAC or 12 VDC For Field Use Two Part Construction Consisting of 24" to 48" Cylindrical Dry Fill Multiplier Tower-Oil Fill Option Available High Current Spark Switch/ Safety Gap High Voltage Indicating Panel Meter Optional Designs Available HVOLT100V - 100KV@3MA (Ready to Use) ......................$1995.95 HVOLT200V - 200KV@1.5MA (Ready to Use) ...................$3495.00 HVOLT300V - 300KV@1MA (Ready to Use) ......................$5495.00 Oil Filled Resistive Loads 33MEG - 33 Megohm, 100,000 Volt, 3000 Microamp, 300 Watt Insertable Element .............$295.00 133MEG - 133 Megohm, 200,000 Volt, 1500 Microamp, 300 Watt Insertable Element ........$395.00 OILBASE - Base and stand with terminations for above elements. 30" height. Uses transformer or vegetable oil, not included ......................................................$150.00 Higher Powered Devices Available On Request, Please Email Us With Your Requirements.

These type of power supplies produce high voltage pulses that can be used for ignitors/ignitions for chemcial detonations, triggers for spark gaps, flashtubes, shockers of all power levels for animals to unauthorized human entry, etc.

We can optionally design a CD power supply to your requirements. Contact us for details.

High Voltage Pulse Trigger Source

Spark gap trigger Flash tube trigger Pyroelectric ignitor Shocker Universal trigger device generates up to 0.5 Joules to an external trigger or pulse transformer. Built in selector switch allows repetitive triggering at an adjustable repetition rate or single manual triggering via a push button switch or a jack for precision external single event triggering. Circuit is powered by a 12 volt wall adapter. Includes a 25 kv trigger transformer for basic applications. Utility unit measures 3-3/4 x 5-1/2 x 2-1/4" and weighs less than 1 pound. IGNITOR10 - Ready to Use With Small 25kv Trigger Transformer ..........$99.95

Medium Power Capacitor Discharge Driver

CD1 - Plans (By Download - $4.00) ...............$10.00 CD1K - Kit/Plans ................................................$99.50

Useful laboratory device intended to pulse drive ignition transformers, CDI coils obtaining pulsed high voltage, high peak current discharges. Capacitor discharge circuitry has adjustable charging voltage pulse discharge rate. An auxiliary input jack is provided for external or synchronized triggering. This driver will produce up to 4 to 5 inch sparks from a good quality automotive ignition coil! Includes a built in 20,000 volt output pulse coil for testing. Adjustable Pulse Rate Up To 100 Reps/Second Adjustable Charging Voltage Up To 350 Volts Pulse Energy Up To 0.3 Joules Operates from 12VDC

TRIG1K/TRIG10

HV Trigger and Ignitor Produces a 20,000 volt 1" open-air spark discharge. On board switch allows selection of a high or low energy setting of 180 and 5 millijoules of spark output energy respectively. Repetition rate is 3 or 30 pulses per second. Input and output have wire leads for easy connecting. Intended for triggering spark gap switches for high-speed coulomb energy transfer, igniting flammable gases and atmospheres. Operates from internal, external batteries or 115-vac wall adapter transformer. Ground referenced output circuit provides convenient interfacing to most three terminal devices. Assembly is 7 x 1 ½" board level construction. Kit is an easy to assemble kit with printed circuit board. Ready to use is board level assembly with connecting leads. TRIG1 - Plans (By Download - $3.00) ..................$5.00 TRIG1K - Kit with Printed Circuit Board ..............$34.95 TRIG10 - Ready to Use(shown) ...........................$54.95

Energy Probe

Probe detects E fields produced by electrical activity and other unknown anomalies. Unit uses no batteries or other sources of power yet detects very weak and virtually un-noticed energy fields. Unit can also provide a three dimensional output "footprint" of medical healing machines such as LAKHOVSKY coils, High voltage generators, Ion machines, Dangerous lightning levels, Power line E field gradients, High frequency radiation from TESLA coils and similar devices. This probe is used by paranormal researchers as seen on some TV shows. This device is for detecting strong E fields, like those from plasma globes, tesla coils, ion generators, etc. It is not intended for weak E fields, like those generated by many household items. If you need something to detect household or weaker energy fields, we suggest our IOD10. The apparatus is electrically balanced and designed in the shape of a wand with a 2 inch brass sphere at its detecting end. The handle is 1” OD x 9” of treated polycarbonate with plated metallic tape wrapped around the ends. A neon lamp indicator flashes upon detection and increases as you get closer to the source, or if the source gets stronger. This handy unit is easy to use and can check the validity of output energy of various healing machines and other radiating products. It is a must-have product for those working in these energy fields. Probe detects: Potential free energy field locations Electric fields produced by ions sources Dangerous static charges Paranormal and UFO energy fields High frequency radiation Weather phenomena lightning High voltage leakage points Plotting a three dimensional footprint of E-fields of HV sources Detects strange and otherwise unidentifiable sources

High Voltage Engineering Design Services	High Voltage Design for Research, Trade, Education and Demonstration
We can design or assist in development of high voltage, high current power supplies, pulse conditioning, high energy, EMP, Marx generators, Tesla coils, voltage multipliers, rail and electrokinetic guns, etc. Our facilities are also available for designing and building action displays for museums and electrical demonstrations.
We Will Buy Your Used or Surplus High Voltage Equipment We are constantly evaluating and purchasing used and surplus high voltage devices and components.
You may contact us or Call: 1-603-673-6493 or Fax: 1-603-672-5406.
Offshore Manufacturing

PO Box 716, Amherst, NH 03031-0716