Pulsers/Chargers
Home | New Products | Gift Ideas | Plans | Policies | Contact Us
Transformer/Coil Manufacturing | Engineering & Design Services
To order: click the ITEM NUMBER
to add to your shopping cart
|
|
Pulsers/ChargersHome | New Products | Gift Ideas | Plans | Policies | Contact Us Transformer/Coil Manufacturing | Engineering & Design Services |
To order: click the ITEM NUMBER
|
)
HEP90 FRONT PANEL |
)
CAPBANK (L) AND REAR VIEW OF HEP90 (R) |
The high energy pulser is a programmable capacitor charging device with a built-in, all tungsten, triggered spark switch.
It can be used for the following electrokinetic projects:
The system is built on a metal chassis of 10 x 17" with a metal control panel of 21 x 8.5".
The panel contains a meter that reads the charge voltage on the capacitor energy storage bank being charged, a safety switch that can be replaced by a key switch, a power control that allows pre-programming the voltage level that the system will charge to, a charge button that must be depressed during the charge cycle, a fire button that triggers the spark switch, and two LED's indicating charging and ready to fire modes.
The electronics uses a 60 Hz current limited core and coil transformer with heavy duty rectifiers and a dv/dt protection resistor. Switching is by a relay and hardened electronics.
The trigger pulse uses our DC integrating system providing reliable firing of the spark switch.
External connection lugs are heavy duty #6 block lugs with set screws assuring a positive connection. All connection lugs are positioned to help reduce power robbing stray inductance. Input power is via a 3 wire grounded cord set.
The HEP90 can be operated with energy storage of 100 to 3000 Joules at voltages from 2 to 6Kv. Low inductance loads will require our trigger pulse blocking cores inserted onto the discharge lines as shown in the set up drawings.
You will note that our PPRO1 - Plasma Thermal Gun, MASS10 - Mass Driver, MAGCAN10 - Magnetic Cannon, WIREXPLOD10 - Wire Exploding, and CANCRUSH10 - Can Crusher, all use this basic system along with the 96Mfd/4.5Kv Capacitor Bank. The individual low cost peripherals can now be purchased for the required projects.
HEP9 - HEP90 Pulser Plans (By Download - $10.00) .......$25.00
Includes plans for our MASS10 Mass Launcher,
CANCRU10 Can Crusher,
WIREXPLOD10 Wire Exploder/Blast Art,
and PPRO1 Plasma Thermal Gun.
|
HEP9K - Pulser Kit/Plans ......................................................$499.95
HEP90 - Pulser Assembled ..................................................$649.95 |
|
HEP90 Will Charge Up To 50 Of The Below Capacitors In Parallel For Serious High Energy Experimentation!
32M/4500V - Storage Caps 325 Joules@4.5Kv ................$199.95
30M/4000V - Storage Caps 240 Joules@4Kv ...................$149.95
Less costly than our HEP9 systems. Provides lower energy yet acceptable classroom performance when used for the MASS1, CANCRU1 and WIREXPLOD1. Operates on 12vdc/115vac or batteries for portable use. Includes 500 Joules of 1-2kv storage capacitors.
|
|
HEP3 - Plans High Energy Pulser/Ignitor ..................................$15.00
High Voltage Engineering Design Services |
High Voltage Design for Research, Trade, Education and Demonstration |
| We can design or assist in development of high voltage, high current power supplies, pulse conditioning, high energy, EMP, Marx generators, Tesla coils, voltage multipliers, rail and electrokinetic guns, etc. Our facilities are also available for designing and building action displays for museums and electrical demonstrations. | |
We Will Buy Your Used or Surplus High Voltage Equipment
|
|
|
You may contact us or Call: 1-603-673-6493 or Fax: 1-603-672-5406.
|
|
|
|
|
|
|
|
Email: Sales & Orders | Email: Tech Support |
|
|
PO Box 716, Amherst, NH 03031-0716 |
|
){kind=link}